Hershine 37 Trawler
About the Hershine 37 Trawler
Researched from public sources for this model. Any individual boat may have been modified or repowered — confirm before relying on any figure.
- Builder
- Hershine (Taiwan)
- Length
- 37 ft
- Propulsion
- inboard
Tank capacities — where the figures come from
-
Fuel unknown
“Fuel capacity 200.0 G Total - 2 Tanks” — broker listing (1979), tacoma.boatshed.com · “Fuel: 200 gal” — broker listing (1987), bluewateryachtsales.comOnly listings give figures, for two boats (a 1979 tri-cabin and a 1987 trunk-cabin Newburyport), and they describe two tanks. No builder or magazine figure was found.
-
Water unknown
“Water capacity 100.0 G Total - 2 Tanks” — broker listing (1979), tacoma.boatshed.com · “Water: 200 gal” — broker listing (1987), bluewateryachtsales.comTwo listings disagree; these may be different layouts (tri-cabin vs trunk cabin).
-
Holding unknown
“Holding tank capacity 40.0 G Total - 1 Tanks” — broker listing (1979), tacoma.boatshed.comOne listing only.
-
Water heater unknown
No builder document, review or listing was found giving a water heater size, or saying whether one was fitted, for the Hershine 37.
Tanks are often replaced or added on older boats — check the tank labels or a survey for yours.
Thrusters and steering — where this comes from
-
Bow thruster unknown
No builder list or review was found. One 1987 Hershine 37 (Newburyport trunk-cabin version) broker listing, repeated on several sites, has a bow thruster with controls at both helms, but that's a single boat.
-
Stern thruster unknown
Nothing found.
-
Steering unknown
No builder document, review or listing found names the steering system (a 1979 tri-cabin listing is silent).
Thrusters and steering are often replaced — check the units on your boat before ordering parts.
Sources disagree on water tank — left blank rather than guessed.
Thin record: no builder spec sheet was found. Hershine, a Taiwan builder, delivered its first trawler in 1977 and built over 1,250 yachts; the 37 was one of its most popular models. Heavily built; single 120 hp Lehman cruises about 7 knots. Production years not confirmed by the sources read.
Engines fitted
-
Ford Lehman 2715E (120) — 120 hp, diesel, single or twin
standard
A 1979 Hershine 37 tri-cabin listing has twin Lehman 2715E 120 hp engines; a 1986 Hershine 37 discussed on Trawler Forum has Lehman 120s (twin per the thread). No builder spec found, so base vs optional layout is not confirmed.Sources: tacoma.boatshed.com · trawlerforum.com
-
Ford Lehman SP135 — 135 hp, diesel, single
factory option
A 1987 Hershine 37 (Newburyport trunk-cabin version) listing shows a single Ford Lehman SP135 with 2,250 original hours.Sources: bluewateryachtsales.com
Boats of the same model can differ — check which engines yours actually has before ordering parts.
Generator
A 1981 Hershine 37 sale brochure (Italy) lists a generator of unstated make and size; owner forum threads discuss generators on individual boats. No builder or review source.
Known problems for this model
-
Window and hatch leaks causing interior water damage deck
Buyers commonly find interior water damage from leaking windows and hatches on Hershine 37s.trawlerforum.com
-
Gelcoat cracking at deck joints deck
Crazing and deep cracks where horizontal and vertical surfaces meet (deck-to-hull, deck-to-cabin, flybridge edges), sometimes with moisture behind them, have been reported at survey.trawlerforum.com
-
Original black iron fuel tanks fuel
Hershines came with black iron fuel tanks, often hidden and hard to inspect; many have been replaced with aluminum.californiayachtsales.com · trawlerforum.com
Engines & parts
Ford Lehman 120 (6D380 / 2715E) parts: good
Factory standard engine — you entered “Ford Lehman 2715E (120)”
Marinized by Lehman from the Ford of England 'Dorset' 2715E six-cylinder (380 cu in) industrial/truck diesel; Ford built the Dorset base engines 1964–1984. Base-engine internals interchange with the Ford 2715E, and marine-specific parts (raw water pumps, heat exchangers, injection elbows, gaskets, lift pumps, air filters) are widely stocked. American Diesel Corp (founded by former Lehman people) still sells parts, publishes spare-parts lists and gives technical advice. Rebuilt and used 120s are also sold by salvage yards.
Parts sources: American Diesel Corp, Go2marine (Ford Lehman parts collection), Fred Warner Marine & Outdoors
Common problems (2)
-
Chronic oil leaks engine
Most 120s weep oil somewhere; owners often trace it to the rear of the engine near the heat exchanger (head/head gasket area) or to the drive seals of the gear-driven injection pump. Moderate oil use is treated as normal on these engines.trawlerforum.com · marineengine.com
-
Fuel leaks at injection pump, lift pump and return lines fuel
Slow diesel drips usually come from loose bleed screws or banjo washers, perished rubber injector return hoses, a failing lift-pump diaphragm, or worn internal seals in the Simms or CAV injection pump, which needs a pump shop to overhaul.yescenters.com
Maker’s service schedule (16)
| Engine oil & filter change | 200 hrs | “After first 15 hours running .... 1. Change Engine Oil ... Every 200 hours running ..... 17. Change engine and transmiss” — manufacturer (1986), marinedieselbasics.com |
| Fuel filters & water separator | 200 hrs | “Every 200 hours running ..... 18. Change all engine and fuel oil filters.” — manufacturer (1986), marinedieselbasics.com |
| Change oil in fuel injection pump | 50 hrs | “Every 50 hours running ...... 13. Check cleanliness of intake air filter. 14. Check (exchanger) zinc pencil. 15. Change” — manufacturer (1986), marinedieselbasics.com |
| Transmission fluid change | 200 hrs or 1 yr | “Change oil every 200 hours of operation or at least once each season under normal conditions” — manufacturer (1986), marinedieselbasics.com |
| Valve clearance check / adjust | 400 hrs | “After first 15 hours running .... 3. Adjust valve clearances. ... Every 400 hours running ..... 22. Adjust valve clearan” — manufacturer (1986), marinedieselbasics.com |
| Injector test / service | 400 hrs | “Every 400 hours running ..... 21. Remove and service injectors.” — manufacturer (1986), marinedieselbasics.com |
| Engine pencil zincs | 50 hrs | “After first 15 hours running .... 4. Check (exchanger) zinc pencil. ... Every 50 hours running ...... 14. Check (exchang” — manufacturer (1986), marinedieselbasics.com |
| Drive belts inspect / replace | 200 hrs | “After first 15 hours running .... 5. Adjust belt tension. ... Every 200 hours running ..... 16. Adjust belt tension.” — manufacturer (1986), marinedieselbasics.com |
| Air filter / intake silencer | 50 hrs | “After first 15 hours running .... 8. Check cleanliness of intake air filter. ... Every 50 hours running ...... 13. Check” — manufacturer (1986), marinedieselbasics.com |
| Clean fuel lift pump | 200 hrs | “Every 200 hours running ..... 19. Clean fuel lift pump.” — manufacturer (1986), marinedieselbasics.com |
| Clean injection pump cover filter | 200 hrs | “Every 200 hours running ..... 20. Clean injection pump cover filter.” — manufacturer (1986), marinedieselbasics.com |
| Remove raw water pump and check drive coupling | 400 hrs | “Every 400 hours running ..... 23. Remove raw water pump and check drive coupling. Place dab of grease on coupling halves” — manufacturer (1986), marinedieselbasics.com |
| Adjust idling speed (if required) | 400 hrs | “After first 15 hours running .... 10. Adjust idling speed (if required). ... Every 400 hours running ..... 24. Adjust id” — manufacturer (1986), marinedieselbasics.com |
| Check engine/propeller shaft alignment | 6 mo | “After first 15 hours running .... 9. Check engine/propeller shaft alignment. (twice annually, minimum).” — manufacturer (1986), marinedieselbasics.com |
| Replace Borg Warner transmission oil cooler | 1,200 hrs | “Suggested replacement is at 1200 hours.” — manufacturer, img1.wsimg.com |
| Inspect drive damper | 2,500 hrs | “Inspect your drive damper if you have more than 2500 hours on the engine.” — manufacturer, img1.wsimg.com |
Service part numbers (3)
| Raw-water impeller | Jabsco 1210-0001 | “6D380 5850-0001 040 3/4" NPT Flange SK33 3298 1210-0001” — manufacturer, marineengine.com · “Breakdown of 2C48 Pump ... 9 1 1210-0001 IMPELLER” — manufacturer, marinesurveyorontario.com |
| Raw-water pump kit original 2C45 pump (Jabsco 5850-0001) |
Jabsco SK33 | “6D380 5850-0001 040 3/4" NPT Flange SK33 3298 1210-0001” — manufacturer, marineengine.com |
| Raw-water pump kit Lehman 2C48 replacement pump (Jabsco 10950-2401 type) |
Jabsco SK239 | “Service Kit SK239 - Comprising Key 7/8/9/17” — manufacturer, marinesurveyorontario.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Ford Lehman 135 / SP135 (2725E) parts: good
Factory optional engine — you entered “Ford Lehman SP135”
Based on the later Ford 'Dover' 2725E 6.2 L naturally aspirated six (Ford built the Dover series 1982–1994, then Otosan/Dovertech to 2005). Parts are sold by the same Lehman specialists as the 120; American Diesel lists spare-parts sheets and Go2marine stocks cooling parts, heat exchangers and elbows for the 135. Do not assume 120 (2715E) and 135 (2725E) internals interchange.
Parts sources: American Diesel Corp, Go2marine (Ford Lehman parts collection)
Maker’s service schedule (14)
| Engine oil & filter change | 200 hrs | “Every 200 hours of operation ..... Change Engine Oil & Filter. And Transmission Oil.” — manufacturer (1987), marinedieselbasics.com |
| Fuel filters & water separator | 200 hrs or 1 yr | “should be replaced once each season or at least each 200 hours (which ever comes first) under normal conditions” — manufacturer (1987), marinedieselbasics.com |
| Raw-water pump impeller | 200 hrs | “Every 200 hours of operation ..... Replace raw water pump impeller.” — manufacturer (1987), marinedieselbasics.com |
| Coolant replacement & freeze-point test | 1,200 hrs | “Every 1200 hours of operation ..... Flush cooling system. Replace anti-freeze.” — manufacturer (1987), marinedieselbasics.com |
| Exhaust mixing elbow inspection | 200 hrs | “Every 200 hours of operation ..... Check exhaust components for leaks.” — manufacturer (1987), marinedieselbasics.com |
| Transmission fluid change Borg Warner gearbox | 200 hrs or 1 yr | “Change oil every 200 hours of operation or at least once each season under normal conditions” — manufacturer (1987), marinedieselbasics.com |
| Transmission fluid change PRM/Newage gearbox | 200 hrs | “After 25 hours running: Drain all oil from the gearbox and refill with one of the recommended lubricants.” — manufacturer (1987), marinedieselbasics.com |
| Transmission fluid change Twin Disc gearbox | 1,000 hrs or 6 mo | “The period between oil changes is 1000 hours of operation or 6 months, whichever occurs first.” — manufacturer (1987), marinedieselbasics.com |
| Check idling speed | 200 hrs | “Every 200 hours of operation ..... Check idling speed, adjust if required.” — manufacturer (1987), marinedieselbasics.com |
| Check coolant and oil hoses | 200 hrs | “Every 200 hours of operation ..... Check condition of all coolant and oil hoses.” — manufacturer (1987), marinedieselbasics.com |
| Check engine mount bolts | 200 hrs | “Every 200 hours of operation ..... Check all engine mount bolts.” — manufacturer (1987), marinedieselbasics.com |
| Replace thermostats | 3,600 hrs | “Every 3600 hours of operation ..... Replace thermostats.” — manufacturer (1987), marinedieselbasics.com |
| Replace Borg Warner transmission oil cooler Borg Warner gearbox | 1,200 hrs | “Suggested replacement time is at 1200 hours.” — manufacturer, img1.wsimg.com |
| Inspect drive damper | 2,500 hrs | “Inspect your drive damper if you have more than 2500 hours on the engine.” — manufacturer, img1.wsimg.com |
Service part numbers (9)
| Oil filter engines built before the 1987 change (original filter) |
Lehman 2N50 | “11 1 2N50 FILTER (Engine Oil Cooler Assembly D196/D197, SP90 / 135)” — manufacturer, marinesurveyorontario.com |
| Oil filter 1987-on engines (larger capacity, revised fitment) |
Lehman 2N53 | “DURING 1987 A NEW OIL FILTER OF LARGER CAPACITY ... THIS IS PART No. 2N53” — manufacturer, marinesurveyorontario.com · “Oil Filter 2N53 LM - P12-R105 P11-88” — dealer, lancingmarine.com |
| Fuel filter | Ford 6149717 × 2 | “2 ALL 2 6149717 FUEL FILTER ELEMENTS” — manufacturer, marinesurveyorontario.com |
| Raw-water impeller | Jabsco 1210-0001 | “Breakdown of 2C48 Pump ... 9 1 1210-0001 IMPELLER” — manufacturer, marinesurveyorontario.com |
| Raw-water pump kit | Jabsco SK239 | “Service Kit SK239 - Comprising Key 7/8/9/17” — manufacturer, marinesurveyorontario.com |
| Drive belt | Lehman 2B209 | “15 1 2B209 VBELT (Alternator Assembly D144, M/N)” — manufacturer, marinesurveyorontario.com · “Alternator Accessory Drive V-Belt 2B209 2B209 - P11-51” — dealer, lancingmarine.com |
| Air filter | Lehman 1F7 | “12 1 1F7 FOAM ELEMENT (Plenum Chamber / Air Filter Assembly D1125, SP135)” — manufacturer, marinesurveyorontario.com · “Air strainer to replace 2H75 & 1F7 (PF136) (Whilst stocks last)” — dealer, lancingmarine.com |
| Zinc / anode | Lehman EM21A | “25A 1 EM21A ZINC ANODE (Heat Exchanger Assembly D882/D883, SP135)” — manufacturer, marinesurveyorontario.com · “Anodes EM21A (Pack of 5) - - P11-18” — dealer, lancingmarine.com |
| Thermostat | Lehman 2C35 | “11 1 2C35 THERMOSTAT ... Modified / 12 1 1541317 GASKET” — manufacturer, marinesurveyorontario.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Model sources (5)
californiayachtsales.com · trawlerforum.com · pacificyachting.com · tacoma.boatshed.com · bluewateryachtsales.com
Own a Hershine 37 Trawler? Add her to your boats, then share a photo — names, numbers and faces are blurred before it appears.
Researched from public sources. Spotted an error? The sources are listed above — tell us what they got wrong.