Custom Boat Manual

Models › Selene

Selene 53 / 55 Ocean Trawler

Built 2002–2014 by Jet-Tern Marine (China)

Own one? Keep her maintenance, manuals and checklists here — free for a week Shopping? Find the right used boat Looking at one? Sea-trial scorecard

About the Selene 53 / 55 Ocean Trawler

Researched from public sources for this model. Any individual boat may have been modified or repowered — confirm before relying on any figure.

Illustration of a Selene 53 / 55 Ocean Trawler
Illustration, not a photo of this model. AI-generated illustration of a typical twin-engine flybridge trawler.
Built
2002–2014
Builder
Jet-Tern Marine (China)
Designer
Howard Chen
Hull / keel
full displacement
Propulsion
inboard
Fuel
1,500 gal
Water
450 gal
Water heater
20 gal · AC + engine · standard
Generator
standard
Steering
hydraulic · Hynautic
Tank capacities — where the figures come from
  • Fuel 1,500 gal
    “Fuel Capacity: 1,500 USG ( 5700 Liters )” — builder, pdf.nauticexpo.com · “Total capacity 1,500 US gallons, two FRP fuel tanks” — builder, trawlers-yachting.com · “The 1,500-gallon fuel tank” — search excerpt (2008), novesea.com · “Fuel Tank: 2 x 550 gal” — broker listing (2010), seleneamericas.com · “The yacht carries 1100 gal of fuel” — search excerpt, shestakovyachtsales.com
    Selene's standard European specification for the 53, a builder document, gives 1,500 US gal. A 2010 boat sold by Selene Americas (two 550 gal tanks, 1,100 in all) and a broker's overview give 1,100, so US-spec or earlier boats may differ.
  • Water 450 gal
    “Water Capacity: 450 USG ( 1700 Liters ); Two FRP water tanks ... total capacity 450 US gallons” — builder, pdf.nauticexpo.com · “Two FRP water tanks w/ shut off valve, total capacity 450 US gallons” — builder, trawlers-yachting.com · “Fresh Water Tank: 2 x 200 gal” — broker listing (2010), seleneamericas.com · “400 gallons of freshwater storage” — search excerpt (2008), novesea.com
    The builder's spec says 450; two listings, from 2008 and 2010, say 400 (two 200 gal tanks). Listings don't override the builder figure, but US boats may have 400.
  • Holding unknown
    “Holding Tank Capacity: 150 USG ( 570 Liters )” — builder, pdf.nauticexpo.com · “One FRP holding tank ... total capacity 80 US gallons” — builder, pdf.nauticexpo.com · “Holding Tank Capacity: 150 USG ( 570 Liters ) ... One FRP holding tank ... total capacity 80 US gallons” — builder, trawlers-yachting.com · “Holding Tank: 1 x 110 gal” — broker listing (2010), seleneamericas.com · “a 100-gallon ho[lding tank]” — search excerpt (2008), novesea.com
    The builder's own spec contradicts itself (150 US gal in the dimensions table, 80 US gal in the plumbing section); listings give 100–110.
  • Water heater 20 gal · AC + engine · standard (Torrid)
    “Torrid 20 gallons 120V/240V AC dual heating source hot water heater” — builder, trawlers-yachting.com
    From the builder's Selene 54' Standard European Specification, hosted by the French dealer and also the source of our tank figures for this model. Its dual heating source is taken to mean an electric element plus engine coolant. The document is titled 54', so it may reflect the later version of this hull.

Tanks are often replaced or added on older boats — check the tank labels or a survey for yours.

Thrusters and steering — where this comes from
  • Bow thruster unknown
    “SELENE 54' STANDARD EUROPEAN SPECIFICATION ... Recessed bow thruster tunnel” — brochure, trawlers-yachting.com · “DC ELECTRICAL SYSTEM ... Maxwell HWC 2200 windlass ... Aqua Signal navigation lights ... (no thruster listed)” — brochure, trawlers-yachting.com · “SELENE 53' STANDARD EUROPEAN SPECIFICATION ... Recessed bow thruster tunnel Integral FRP stern thruster casing” — brochure, pdf.nauticexpo.com
    The builder's standard European specification (titled 54', the same 18.24 m hull as the 53) molds in a bow-thruster tunnel, but its standard DC electrical equipment list has no thruster unit, unlike the Selene 38 spec. That makes our earlier figure of standard doubtful, and no option list was found to settle it.
  • Stern thruster unknown
    “Integral FRP stern thruster casing” — brochure, trawlers-yachting.com
    The standard specification provides a stern-thruster casing in the hull but lists no stern thruster unit, so our earlier figure of standard isn't supported.
  • Steering hydraulic · Hynautic
    “STEERING SYSTEM • Hynautic hydraulic steering system for pilothouse & F/B” — brochure, trawlers-yachting.com
    The builder's standard European specification gives Hynautic hydraulic steering at pilothouse and flybridge, with a teak wheel inside and a 30-inch stainless wheel on the bridge. The document is headed 54' but carries the 53's dimensions; US-market boats weren't checked.

Thrusters and steering are often replaced — check the units on your boat before ordering parts.

Sources disagree on hp (standard single Cummins), hp (twin QSB option), holding tank, bow thruster, stern thruster — left blank rather than guessed.

Selene's most popular model: the 53 (sold as the 55 in 2005-09) became the 54 on new molds. The only spec table found (HMY) is for the later 54 (59.83 ft LOA, 16.67 ft beam, 5.67 ft draft, 1,500 gal fuel, 400 gal water, 110 gal holding), so dimension fields are left null for the 53/55. Three staterooms; standup engine room off the master. Most have a single Cummins (430 hp quoted) plus wing engine; many 53s were twin-engine. Bow and stern thrusters listed.

Engines fitted

Boats of the same model can differ — check which engines yours actually has before ordering parts.

Generator

standard

“Northern Lights 12Kw. generator w/ sound shield, muffler and remote start switch panel located in P/H, including dedicat” — builder, trawlers-yachting.com

The US Selene dealer's 55 page says many 55s have a Northern Lights 12 kW behind the main engine.

Generators are often replaced or added — check the unit's own plate before ordering parts.

Known problems for this model

Engines & parts

Cummins 6BT / 6BTA 5.9 parts: good

Factory optional engine — you entered “Cummins 6BTA5.9 (330 hp)”

Mechanically injected 5.9 L inline six from the Cummins B-series truck/industrial family, so base-engine parts are everywhere. Cummins still sells factory ReCon (remanufactured) marine 6BT/6BTA engines (152–210 hp ratings) with a 2-year/2000-hour warranty. Seaboard Marine is the best-known marine specialist, selling aftercooler/heat-exchanger service kits, upgraded raw water pumps and technical guidance; TAD also sells Cummins packages.

Parts sources: Seaboard Marine, Cummins (ReCon 6BT/6BTA), Diesel Pro Power

Common problems (2)
  • Aftercooler corrosion letting seawater into the intake cooling
    On the turbo-aftercooled 6BTA the seawater-cooled aftercooler core has vertical tubes and an aluminum housing that corrodes from condensate; a leak can put salt water into the cylinders and wreck the engine. Owners pull, clean, grease and pressure-test the core every few years and fit new O-rings.
    trawlerforum.com · sbmar.com
  • Heat exchanger and aftercooler service cooling
    Routine seawater-side service (O-rings, gaskets, zincs) is a recurring owner job; kits are sold for it and refilling coolant without trapping air is a common question.
    sbmar.com · sbmar.com
Service part numbers (5)
Oil filter Cummins 3937743
“| Oil Filter | 3937743 |” — dealer, marineenergy.com.au · “Cummins Oil Filter 3937743 Spin-on type, 3.66" outside diameter, 6.95" height” — dealer, dieselpro.com
Fuel filter
6BT 5.9 210 hp (CPL 742)
Fleetguard FF5052
Replaces FF42000, FS1251
“on-engine fuel filter with drain for all 6BT 210 B’s (CPL 742). Replaces the FF42000, FS1251.” — dealer, sbmar.com · “Cummins 6BT Fuel Filter 3931063 FF5052” — dealer, marineenergy.com.au
Fuel filter
late 6BTA (also late 4BTA and 6CTA)
Fleetguard FF5285
“Fleetguard FF5285 Fuel Filter – late 4BTA 6BTA and 6CTA’s” — dealer, sbmar.com · “Cummins 6BTA Fuel Filter 3890017 FF5285 ... suits late model Cummins 6BTA's, 6CTA8.3-M” — dealer, marineenergy.com.au
Raw-water impeller
seawater pump with 1-1/4 in hose ports (Sherwood M70/M71 type, early 4BT/6BT)
Sherwood 10615K
“Seawater Pump Impeller | **1-1/4" PORTS** 3908220 10615K” — dealer, marineenergy.com.au · “Cummins Marine Water Pump Impeller 10615K 2 9/16" diameter, 1 5/8" length” — dealer, dieselpro.com
Raw-water impeller
keyway-shaft pump, 2 in inlet / 1-3/4 in outlet, 11° offset flange (e.g. P1716/P1730 on 6BTA)
Sherwood 17000K
“**2" inlet & 1-3/4" outlet ports with 11° OFFSET flange** 17000K” — dealer, marineenergy.com.au · “Cummins Impeller for Key Shaft 17000K” — dealer, dieselpro.com

From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.

Cummins QSB 5.9 parts: good

Factory optional engine — you entered “Cummins QSB”

Electronically controlled (common-rail) successor to the mechanical 6BTA; current Cummins dealer network plus marine specialists such as Seaboard Marine supply parts. Electronic diagnostics require dealer tools more often than on the 6BTA.

Parts sources: Seaboard Marine, Diesel Pro Power

Common problems (3)
  • Raw water pump leaks cooling
    Owners most often report the seawater pump leaking or being replaced around 1000 hours; an improved pump version is available. Some also updated fuel coolers as a precaution.
    forums.ybw.com
  • Aftercooler service and cracking cooling
    As with the 6BTA, the aftercooler needs periodic removal and resealing; a cracked aftercooler is generally replaced rather than repaired.
    trawlerforum.com · facebook.com
  • Burnt intake valves / loss of power engine
    Seaboard Marine forum threads describe burnt valves and high-rpm power loss on some QSB 5.9s.
    sbmar.com
Service part numbers (5)
Oil filter Fleetguard (Cummins-specified) LF3959
Also: Cummins 3937743
“MMK001SK59 QSB5.9 Marine Service Kit ... LF3959 Oil Filter 1” — manufacturer, cummins.com
Fuel filter Fleetguard (Cummins-specified) FF5488
“MMK001SK59 QSB5.9 Marine Service Kit ... FF5488 Fuel Filter 1” — manufacturer, cummins.com
Fuel pre-filter / separator Fleetguard (Cummins-specified) FS20402
“MMK001SK59 QSB5.9 Marine Service Kit ... FS20402 FS Filter 1” — manufacturer, cummins.com
Drive belt
serpentine belt, post-Jan 2008 QSB 5.9 with 21/22SI or 24SI alternator (brown belt)
Cummins 4981117
“Cummins Serpentine Belt for QSB 5.9 (post January 2008) 21/22 SI Alternator CPN 4981117 (BROWN)” — dealer, sbmar.com · “4981117 Alternator Belt for Cummins® QSB 5.9 Engine” — dealer, seapowermarine.com
Cummins QSB5.9 marine service kit (zincs, oil, fuel and FS filters, minor water-pump kit) Cummins MMK001SK59
“MMK001SK59 QSB5.9 Marine Service Kit” — manufacturer, cummins.com

From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.

Steering

Hynautic — K-series pressurized hydraulic steering (H-series helms, K-series cylinders) parts: obsolete

SeaStar bought Hynautic and kept making components and rebuild kits for years; after Dometic bought SeaStar, Hynautic pages and parts were removed from Dometic's site. Helms H-21 through H-52 and cylinders K-6 through K-31 are discontinued. Seatech Marine Products publishes SeaStar direct-replacement equivalents (e.g., H-50/H-52 replacement kits usable in the pressurized system with a non-vented fill plug) and offers rebuild services; independent hydraulic shops rebuild helms and cylinders for roughly $250–350 each. Kobelt/Accu-Steer also supply steering and power-assist equipment used on larger boats.

Parts sources: Seatech Marine Products (Hynautic alternatives & rebuilds), Kobelt (marine steering systems)

Common problems (3)
  • Helm pump shaft seal leaks steering
    The upper helm shaft seal deteriorates from sun, salt and dirt and weeps oil; raising system pressure is only a stopgap, and the helm must be removed and resealed.
    samsmarine.com · trawlerforum.com · youtube.com
  • Cylinder rod seal leaks steering
    Damaged wiper/rod seals let fluid out the end of K-6 type cylinders.
    facebook.com
  • Olive-type tubing fittings leak steering
    Some owners dislike Hynautic's olive compression fittings on plastic tubing because they are prone to leaks.
    trawlerforum.com
Model sources (9)

hmy.com · trawlerforum.com · powerboatmagazine.co.nz · alexandermarineusa.com · trawlerforum.com · seleneamericas.com · pdf.nauticexpo.com · trawlers-yachting.com · selene55.com

Own a Selene 53 / 55 Ocean Trawler? Add her to your boats, then share a photo — names, numbers and faces are blurred before it appears.

Other Selene models

Researched from public sources. Spotted an error? The sources are listed above — tell us what they got wrong.